Related Products

Quest Impact Attenuator System
The QUEST System is a simple redirective, non-gating crash cushion that has been completely tested and has successfully passed the entire NCHRP 350 test matrix at test levels two and three. The 70mph Quest System has been tested and accepted by the FHWA after successfully passing NCHRP 350 test 3-31. The QUEST System consists of a series of W-beam fender panels supported by diaphragms with an innovative integrated trigger mechanism at the nose that releases a “front assembly” during impacts to absorb the energy of impact. The system is designed to telescope rearward during head-on impacts to absorb the energy of such an impact and to redirect vehicles during side angle impacts. The system provides protection for hazard widths ranging from 24”-36”.
”
- Non-gating, redirective impact attenuator
- Performs effectively with design speeds up to 100 km/h (62 mph)
- Meets NCHRP 350 TL-3 (100 km/h / 62 mph)”

RAINPANT ONLY LG/XL LIME
- Waterproof material with durable seam sealed construction
- 2″ wide CNSS reflective material
- Zipper/storm flap closure for weather protection
- Non-sparking snaps and zipper
- Adjustable wrist cuffs
- Lower front patch pockets with snap closure
- Left chest radio pocket
- Adjustable leg cuff straps
ANSI/ISEA 107 2010 Class 3 Compliant – Jacket. ANSI/ISEA 107 2010 Class E Compliant – Pants.

Brush White Wash, No handle
- Soft tampico bristles spread out wallpaper without scratches or folds
- Two rows of bristles with 2-1/2″ trim are set in 8″ hardwood block with tapered handle hole
- Order handle separately

Asphalt Lute
36″ Lute head with 7′ handle
Use an asphalt lute to ensure that asphalt is spread quickly and evenly. Level and smooth asphalt with a variety of head and handle options. Order complete tool or individual replacement components separately. The handle is made of light weight magnesium. A slightly thinner wall thickness on our economy grade line reduces the overall weight while the slightly larger handle diameter assures reasonable strength against bending. A slightly smaller handle diameter on our premium grade line allows hands to relax more while working and allows a heavier wall thickness to resist bending, without increasing the weight of the lute. No angle braces are needed. The end is capped with a rubber tip. The head is made of wear-resistant aluminum alloy. Aluminum alloy holds heat better, making scrape off easier and teeth will not bend easily as with magnesium heads. An 1/8” thick tee-beam has a smooth edge on one side and serrated edge on the other. The smooth edge is used for final finishing pass leaving asphalt ready for compaction. The serrated edge has blunted teeth with rounded notches, permitting mix to flow through easily without “gumming up.” Standard head is serrated with a full tooth at each end. An un-serrated head with a smooth edge on both sides is available upon request.

NAILS CASE HARD CUT #10 50-LB.
3 inch length
5/16″ head
Fluted
Approx. 78 each per pound
Hardened steel with blunt point and tapered shank cause minimal spalling during penetration and offers even greater pull-out resistance than wire masonry nails. Ideal for attaching wood members to cinder block walls as well as to fresh concrete.
NCI SKU: EN1015

Lime Brilliant Series Bomber Jacket
- Durable water proof and seam sealed shell
- Removable black quilted liner
- Hidden collar hood
- 2” wide 3M™ Scotchlite™
- Reflective Material with 3” contrast
- Reflective piping on collar, shoulders, hood and sleeve seams
- Adjustable cuffs
- Black bottom front and cuffs for durability
- Left chest radio pocket
- Two outside lower slash pockets with zippers
- Inside wallet pocket

Nylon Extra Rope
Our Nylon Extra Rope is reinforced with polyester yarns for increased abrasion and U.V. resistance. This rope is perfect for marine, utility, and general industrial use. We carry a complete line of sizes across the country. Standard put up is 600' spools.
Reviews
There are no reviews yet.